Baby handprint. Casts of children's hands and feet: frozen moments that will delight all your life. Salt dough mold

FINALLY FOUND THE TECHNOLOGY HOW YOU CAN DO IT BY YOUR OWN HANDS AND NOT BUY IN THE SALON AND WHETHER TO RUN IN SEARCH OF SPECIAL MATERIAL

1. Making an imprint of a child's hand and foot

For this we do salty dough. You will need: 2 cups flour, 1 cup salt, water, 1 scoop hand cream or vegetable oil(but it's better to add wallpaper paste or PVA, who has what). It is better to make more dough (x2) in order to make more casts, so that there would be plenty to choose from. So from these components you knead the dough, roll it out 1-1.5 cm thick (it is better to roll it out immediately on a baking sheet so as not to shift) and make casts of your baby’s hands and feet on it. Then this dough is baked in the oven at a low temperature for 2-3 hours.

2. Filling the prints

You will need gypsum, but you can also use ordinary gypsum putty (sold in hardware stores).

Now you have your baby's hand and foot prints from salt dough, when they are cool after baking, you grease these forms with petroleum jelly. Then mix gypsum (or putty) with water (sour cream consistency) and fill in the molds. Then all this dries for 1-2 days, if gypsum, if putty was used, then it dries longer than 3-4 days. Then carefully remove the molds from the mold.

3. Sanding or priming impressions

The casts are rough, they need to be sanded (this can be done with a nail file), only very carefully so as not to disturb the lines of children's arms and legs, or, as an option, primed (dilute gypsum with water, dip your finger into it and prime the bumps with your finger).

Here only your imagination will help you. You can cover the sinter with silver acrylic paint, use a photo of a child, designed in Photoshop, as a background.

I get sick of things like this

When I saw such blind people in a photo salon, I set out to find how this can be done

And here I am sharing with you!

one more way:

Master Class:
1) We take the old plasticine, more (or new, better wax, for example "LUCH" - it is softer than the rest), knead it as much as possible, but not to a liquid state (for this you can put the plasticine in a plate on the heater or just a little bit in microwave); it should be very soft, all folds and lines depend on it.
2) We make a cake, uniform in 3 cm, no less. Then we heat it again, and strongly apply evenly the handle or leg of the little one, somewhere to a depth of 1-1.5 cm.
If it's a little off, correct it. Then put it all in the freezer.
3) When the plasticine freezes, we take it out, but before that everything should be prepared: 1 glass of gypsum (you can build it, you can use it for modeling, but it’s better to take it from a children’s kit for creativity, it’s better); 0.5 cups of cold water (add a couple of tablespoons of PVA glue to the water, but do not overdo it, then the plaster figurine will be stronger); some container, so that later it would not be a pity to throw out the stirring stick. The proportions of water and gypsum may be inaccurate, it all depends on the quality of the gypsum, the mixture should be like sour cream in consistency. Pour gypsum into a container, quickly add water and quickly mix until a homogeneous mass (IMPORTANT! Add water to gypsum, and not vice versa !!!).
Hardening of gypsum 5-8 minutes - we do everything faster.
4) Then pour the solution into the prepared cast, if the cast is very deep - 2 cm is enough. If something got out of the edges, there is time to wipe it with a cloth, otherwise there will be ugly edges. ALL!
5) Now let it dry all night!!! When all this is dry, hold your work on heat, put it on the battery, the plasticine will melt, bend the edges - it's easier to take it out! Remove carefully. Carefully level the ugly edges with a nail file.
6) Well, now it all depends on your imagination / possibilities. We paint the trace / paint / or just open it with varnish ... Insert it into a frame / hide it in a box / hang it on the wall ...... ...

Currently, many parents make casts of children's arms and legs with their own hands. Such a commemorative imprint looks very cute and will allow you to remember the wonderful moments of early childhood for many years.

Do-it-yourself casts of children's hands and feet

To make casts of handles and legs with your own hands, you do not need experience, you just need to carefully read the instructions. As a rule, kits contain all the necessary materials and tools. In addition, they often provide the opportunity to make several casts, because working with a child is completely unpredictable, and whether a perfect outline is obtained depends largely on our small models.

How to prepare for a do-it-yourself volumetric cast of arms and legs:

1. take care of the good mood of the little model;
2. you can use sleep time;
3. residue from the mixture after making can be difficult to wash off, so wear clothes that you don't mind getting dirty;
4. the participation of two adults is necessary - one to take care of mixing the ingredients, the second to hold the baby and distract him;
5. if you have touched the sides or bottom of the mold, you can pour plaster into it and then smooth out any imperfections with sandpaper;
6. the time during which the mold completely hardens depends on the temperature of the water used - than colder water, the longer it will harden, the warmer the water - the faster the material will harden, room temperature water is optimal;
7. make sure the containers are the right size for your baby's foot or hand.

How to prepare a child for making a cast of children's arms and legs with their own hands

How to prepare molds for casting casts for children with your own hands

To make an impression with your own hands, mix the powder for the form with water in any container and pour into a closed Plastic container, you can mix the mixture directly in the same container. Be sure to measure the ingredients accurately as a poor ratio can affect the final result. You can use the test sample, which is sometimes included with the kit, to have information about the curing process.

Wet the skin of children's feet or hands thoroughly so that they easily slide out of the hardened mold.

Thanks to this manipulation, your child will be able to get used to the temperature of the mass, in addition, we will minimize the risk of air bubbles that impair the quality of the product. Guide the baby's hand so that it slides accurately and gently into the prepared paste.

Don't worry if your child moves his arm. The beginning of the hardening process will show a change in the color of the paste, and this is the point at which the child should not make very sudden movements. After hardening (about 1-1.5 minutes), remove the handle. To avoid holes in the hardened form, guide the child's hand without touching the bottom or sides of the container.

How to prepare and pour plaster

Plaster pouring should not last longer than 5-6 minutes.

1. Prepare a plastic bowl, measure the right amount of water and gypsum in the appropriate proportions. Always add powder to water, not the other way around;
2. Pour the gypsum into the water slowly, with constant stirring, until the mass reaches the consistency of a very thin yogurt. Too intensive and long mixing can lead to the fact that the mass begins to harden already during pouring into the mold. Also, too much agitation can cause bubbles to form. If you see bubbles on the surface, tap the container a few times to get them out;
3. Initially, the plaster is very watery, but after a while it gently begins to thicken. Gypsum is ready when it reaches the consistency of pancake dough. Then, pour a small amount of gypsum into the mold and carefully move the container in different directions so that the mass fills exactly each hole;
4. After filling the mold 1/3, tap the container on the table surface;
5. Pour the rest of the mass in batches;
6. Leave the container to harden for several hours.

How to avoid air bubbles in plaster?

Air bubbles spoil volumetric casts, as a result, the plaster does not reach the fingertips, and the impression will not completely repeat the child's hand. This problem mostly occurs with pen impressions, as the fingers are longer on them than on the toes, and the plaster does not always flow well into these holes.

You can use the following methods to avoid this:

In what position is it most convenient to make 3D casts

0-5 months. For the smallest children, it is necessary to carry out the procedure in a supine position, as for feeding.

5-12 months. Place the baby sideways on one knee to the parent, legs should hang freely. Make an "airplane": the parent holds the baby on his stomach with his hands, the arms hang freely. In a sitting position: the parent places the child on his knees, facing the table.

After hardening, carefully sand the product. After painting with paint, this treatment will become invisible.

How to make casts of arms and legs with your own hands

The resulting casts can be processed in different ways:

You can add photographs of a baby at the age at which the print was made, and create a themed background, such as a footprint in the sea sand.

The resulting souvenir will delight you, and you will be able to enjoy this memorable and beautiful thing for many years.

I wanted to make some unusual birthday present from my son to my grandmother and aunt. Of course, to this gift I also added the usual gift from my mother :) But that's not about that now :)

I came up with the idea to do imprint pens child from dough for grandma and imprintlegs for aunt. Our loved ones loved this gift!

In addition to the fact that such a craft is a great gift and a wonderful educational activity for your child, the mold is made quickly and easily enough. You can also involve small children in this activity. For example, my son was a year and a month old.

So let's start cooking. imprintlegs and arms of a child made of dough.

1. Cooking dough.

For the test you will need:

- 1 cup of flour (you may need a little more, start with a glass, and then, a little bit, you will add);

- 0.5 cups of salt;

- 125 ml of water;

- 1 tbsp PVA.

- to make colored dough, you can add gouache.

1. We form an imprint.

The test is obtained for 2 crafts. Therefore you can:

- do imprintone handle and one leg;

- 2 handles;

- 2 legs;

We take the first ball and roll out a pancake of the desired size and thickness from it, as you visually like. The resulting pancake immediately put on a baking sheet covered with parchment paper. We take the baby’s arm or leg, hold it tightly and press it into the dough. The dough should not be sticky, but if it is, brush the handle/leg with sunflower oil.

Do not forget to make a hole for the tape if you want to hang the craft.

For me, the most difficult thing was to take my son's hand / foot and make a beautiful print. The son was spinning, moving his fingers, trying to immediately dig into this test ... :) Therefore, we did not succeed in making an imprint from the first attempts. Therefore, do not be discouraged if the first time you do not succeed either, let the whole process become an exciting and fun game for you :)

1. We decorate the craft to your taste.

I lightly decorated with Easter sprinkles and made the prints with a bump around the edges. When choosing the type of jewelry, you need to take into account an important point - if you dry the cast in the oven, choose materials that are resistant to high temperatures. During drying in the sun, you can choose any materials.

1. We dry the mold of the child’s arms / legs from the dough in the oven.

I dried the craft as much as possible in the oven, and then slightly dried it in the room.

We send the craft to the oven at a temperature of 80 degrees and dry for about 2 hours. Ovens are different for everyone, so you need to follow the craft. You will feel when it is ready: the dough will be light in color on top, firm and slightly ruddy on the bottom.

The temperature setting in my oven does not work, so I dried it by eye. And another interesting moment. I did crafts in 2 visits on different days: first a cast of the handles, then a cast of the legs. The casts of my legs began to swell. I did everything the same, except that I put the cast of the pens in a cold oven and the temperature was slightly higher. Perhaps the reason lies precisely in this. When I saw that the cast of the legs was slightly swollen, I pierced a couple of holes with a toothpick. Despite everything, the cast of the legs turned out to be pretty too. To hide the flaws, I tinted them with yellow paint.

1. Last steps.

After the crafts have cooled, they can be decorated with gouache to your taste. I like the unpainted version better :)

We put on ribbons and gifts are ready, and this is also a great memory of the baby. Sign the date or age of the child with paint on the back of the craft.

Here are my options.

1. Craft "Footprint and child's hand from dough" as an educational activity.

At the time of preparation of the craft, my son was 1.1. He himself could not yet make prints, decorate, etc. But despite this, we got a great developmental activity:

- the son crushed and tore the dough with his fingers;

- touched the flour mixed with salt with his fingers. I also added pebbles, cones, sticks there and got a small sensory box. The son poured the materials of the box with a spoon into the vessel.

- I made a cast of a leg for my son, and he felt the shape of his leg with interest;

- the son laughed when I made prints of his legs.

There was a lot of cleaning, but I do not regret it at all :) We are not afraid of cleaning at all.

The most beautiful phenomenon created by nature is the birth of a child.

In the modern world with various kinds technology (camera, video camera) you can track the development of the baby from the very first day of life.

But many people want to look at their baby not only from photographs and videos. Therefore, they often order in studios the so-called copies of the arms and legs of a child - casts that can be made from almost any hardening material - gypsum, chocolate, wax, liquid glass and other materials.

But in this article we will focus on other types of casts - the so-called 3D casts. In another way, they are also called voluminous.

On the Internet you can find the very technology of their manufacture, but rarely where you will see information about their component composition. In this publication, we will reveal this secret to you.

So, to make a three-dimensional cast of a child's arms or legs, we need:

- gypsum (or other hardening material)

- alginate (sold in dental stores)

- plastic container

- water (36.6 degrees)

Before you start work, you need to put your child to sleep in a playpen or a baby cradle (if the little one is still small). This is necessary so that during the removal of the impression, he does not move the handle or leg.

Then we prepare the impression mass. To do this, select the right amount of alginate powder and water in accordance with 1.5 to 1.

Pour the alginate into the water (and not vice versa!) And stir with a mixer or a spoon. Just do it very quickly, as it freezes almost immediately.

Then we immerse the baby's handle (leg) in this mass, wait for solidification. Whether it has frozen or not, you can check with your finger - touch the surface of the mass - if it does not stick to your hands, then the solidification is over. As a result, it should look like rubber.

Now, very carefully, so as not to damage the impression mass, we take the child's limb out of it, and put it back to sleep under the supervision of a baby monitor or video baby monitor. We will get a kind of deepening.

The next step is to prepare a solution of gypsum and water. Pour gypsum into water (and not vice versa!) And stir it to a consistency thick sour cream and fill the resulting cast with this solution. We are waiting for a day. Then we carefully cut the alginate along the edges of the container with a knife, turn it over and make an incision on the mass in order to pull out the resulting cast.

That's all. As they say, everything ingenious is simple. Now the voluminous cast of your crumbs will be preserved for life and constantly remind you of the moments of his childhood.

The company "Chameleon" offers to try an interesting business: Making compositions with casts of baby's arms and legs, 3D copies of newlyweds' hands, commemorative medals with handprints, casts of paws of pets.

What it looks like:

Formats

This business can be done at home or open a point in a large shopping center, offering a wider range of services.

Format "House"

Under the condition of working at home, orders are accepted as follows. The client makes a phone call. The time and date of arrival of a specialist at home are discussed. At the appointed time at the client's home, the necessary blinds are removed, the baby is photographed, and the design option is discussed. All conditions are recorded in the order form. It also reflects the amount of prepayment for the composition, a sales receipt is issued. The master takes away the casts and all the rest of the work on filling and further designing the composition, and spends it at home.

The finished work is delivered to the client at home or he independently picks it up at the place indicated by the master, if necessary, pays the remaining amount.

Format "Studio"

Subject to work in the studio or the availability of retail space in the shopping center, orders are accepted there on the spot by the manager or by phone. Casts can be taken both in the studio and at the customer's home at his discretion. The advantage of going to the client's house is that such conditions are more comfortable for the baby, there are familiar toys and environment nearby.

As you can see, the business is quite simple, it does not require special knowledge, significant investments, all you need is a desire, and in everything else we will help you, from technology to business advice.

The target audience

Potential buyers are: loving parents, grandparents, godparents. Families with average income and above average. The age of the main client is from 23-45 years.

Ways to promote

The target audience is informed about this service by placing advertisements in: maternity hospitals, kindergartens (nursery groups), photo salons and photo studios, children's goods stores, registry offices. The main thing in this business at the beginning of work is to make yourself known through advertising in the above places, placing ready-made sample compositions in places where potential customers congregate. In the future, "word of mouth" gives a good effect.

Key Features

The main features and benefits are:

• lack of license and special permits
• minimum investment
• high profitability
• quick payback
• opportunity to showcase your creativity
• great job for mums on maternity leave
• Office is not required, work from home is possible
• almost no seasonality

Technology

The technology for making casts of pens is quite simple.

1. A very plastic, soft reusable material is used, which allows even the smallest children to take impressions from birth.
2. The process of making an impression takes several minutes. After that, the master takes away the casts and fills them with gypsum mortar at the workplace, after the gypsum has hardened, the product is processed if there are defects and left for further drying.
3. While the casts are drying, you can process the photo in the program.
4. Next, the composition is assembled - all elements are glued to the base and inserted into the frame.

The time spent on making one fully designed composition is: 1 day, of which 12 hours for drying the casts (this process can be accelerated by drying the casts in the oven), immediately leaving to the client, processing the photo and printing it.

What equipment is required to start this business

Basic equipment

No special equipment is required, and what is listed is already in almost every home.

The printer in this case is not required, because.

in any case, printing of large formats of photographs for compositions is carried out in a photo salon.

For work, plastic containers are required in the form of disposable plates for taking impressions, 1.5-3 liter containers for 3D copies of hands, a mixer or a mixing spoon.

How much money do you need to get started?

• Basic equipment: 25,000
• Accessory: no
• Purchase of raw materials and consumables 1,500 rubles.
• Buying a business package - from 5300 rubles.
• The cost of an advertising company - from 3000 rubles.
• Total: 34,800 rubles.

How much can you earn on this?

The cost of making one cast using reusable material is 10 rubles, including plaster and paint.

Baguette frame with glass (framing workshop) - 500 rubles.

We create casts of arms and legs ourselves using alginate gel and gypsum

and above, depending on the baguette option

Composition layout:

• photo collage and decorative elements — 100 rubles.
• decoration for a frame without glass - 100-200 rubles.

The total cost of the composition is 600-700 rubles.

Retail price

The price of a 30x40 format composition with two children's casts is 2,000-5,000 rubles.

As a result, the income from one composition is 1300 - 3500 rubles.

According to practice, for a city with a population of 150 thousand people, the average number of orders per month is 20 pieces, i.e. net profit of about 30 -35,000 rubles. (provided that you are running a business at home). Return on investment: 1.5 -2 months

The offer of the company "Chameleon"

By purchasing a business package from us, you get at your disposal a detailed guide to creating your own impression business, in which we transfer all our experience and knowledge to you.

Depending on the type of business package, you get a set of materials and a personal website to start your new business.

Plus, you will be provided with free consulting support on all issues of running this business and without time limits.

December 2015 update

Another option for opening a studio for making casts of arms and legs is offered by the company "Present Day" (investments from 30,000 rubles). You can read the terms of the franchise or leave a request below for detailed information about the proposed business model.

Contact details

• Company "Chameleon"
• mob. 8 913 792 7363, 906 965 6423
• Skype: hameleon2108
• Email: [email protected]

Questions and answers on the topic

view all (1)

We make casts of children's arms and legs with our own hands!

Home — Articles — We make molds of children's hands and feet with our own hands!

Hello dear readers, finally I am ripe for a new article!
A year and a half has passed since the last inspiration!
A lot of new things have happened in my life, the most important thing is that my son, Leonid, my second child, was born (in January 2014)!
He is now 6.5 months old. And I again started a business with casts!

How to make a mold of the arms and legs with your own hands from plaster? We answer: "Very simple!"


There are a lot of kits for making them in stores, and there are a lot of them on the Internet. different advice how to do it!

In 2011, 3 years ago, when I was making casts of Danochka's arms and legs, I first bought a ready-made set.

How to make a 3d cast of a child's arms and legs at home

I did everything according to the instructions. She diluted the mixture, put the sleeping child’s hand into a plate, and my Danulya took it and woke up and knocked over all this liquid on me! While I was washing, the second jar of gel dried up. Conclusion: I threw money away!

Then I got into my favorite Internet, and saw a lot of recipes for making children's casts from gypsum.

I want to tell you the simplest and easy way making casts of my favorite arms and legs, which I liked the most!

To make children's casts you will need:


For test:
- half a glass of water,
- two tablespoons sunflower oil,
(oil is needed to make the dough more elastic)
- one glass of flour
- one glass of salt
(preferably fine, salt is needed so that the dough is “obedient”, so that it keeps its shape better)

The volume of my glass is 150 milliliters.

To make the casts themselves:
- gypsum,
- water.

Where can I get plaster for making children's casts?

1. You can buy on the construction market.
2. You can buy any children's kit for creativity, for example, the Sculptor kit.
I have had this set since 2011 🙂

First we make the dough.
In a bowl, mix salt and flour, pour in oil and water, mix everything.
The dough should be tight! If the dough is runny, add more flour.
Divide the dough in half and roll it out with your hands.
It is necessary to get two small round, but thick (2-3 cm) cakes, so that the cast is more voluminous.


We take a little one, make prints of the legs and handles!

Making a baby footprint


Making an imprint of a child's hand


For the first time with Dana, I made the right arm and the left leg.
The second time with Leonid, I made the right arm and right leg.
It is better to do as the first time, for example, the left arm and right leg or vice versa.
I think it looks so beautiful!

Next, take a disposable glass, pour water, pour gypsum and mix everything.
I don’t specifically write the proportions of water and gypsum, since I made liquid gypsum “by eye”.
The consistency should be like sour cream or kefir.

We pour liquid plaster into our children's prints, and wait.


When the plaster has hardened, remove the dough and our casts are ready!


The rest of the dough is easily removed with ordinary water.
Baby molds are ready!


It remains to decorate them!

You can color the casts as you like, I took pink and silver nail polish!
First, she painted the children's casts with pink, and then with silver varnish.
Here's what happened.


Then I found a beautiful frame on the Internet, added a photo of the child and signed the age - I printed the photo!
I bought a regular photo frame, put a photo, a pregnancy test, a bracelet and a tag from the hospital!
I glued the finished children's casts, on double-sided tape, on glass!

So a beautiful frame with children's casts is ready for a long memory!

You can add baby's first clothes, a pacifier, and more.

For comparison, I post a photo of my first frame with casts!


Now we have this beauty at home:


Children's casts can be made at any age, but to make it easier to attach them, it is better when they are still tiny.
The sooner you make casts, the easier it is to attach them to the photo frame!

Good luck with your creations!

P.S. : The only thing I didn't understand is how to remove air bubbles from plaster?
Small dots appear on the casts.
Maybe you need to stir longer?

What to give grandma for March 8? Gifts from grandchildren are the most expensive, so grandmothers will be happy with everything. It is especially important that the baby takes part in the preparation of the gift. Here is one of these gifts today I want to offer and show how to make salt dough for baby footprints.

When I saw this idea for the first time, it captivated me. No, it is not new, but the simplicity of its implementation immediately prompted the desire to repeat it to myself. Hope it inspires you too.

Necessary materials

• salt- 1 glass
• flour- 1 glass
• water- 1/2 cup
• rolling pin for rolling dough
• kitchen knife
• acrylic paint
• tassel for drawing

How to make footprints on salt dough

1. Cooking salt dough

Mixing salt (1 cup), flour (1 cup) and water (1/2 cup). Mix everything well to get a homogeneous dough.

The child can also help in this process. With his little fingers, he will really like to interfere with the dough.

2. Cut out the heart

Roll out the dough with a rolling pin to make plate about 1.5-2 cm thick.

Cut out a heart

Put the heart on a baking sheet. I also covered the baking paper, but because of this, the bottom of the heart turned out to be uneven. It would probably be better to just put it on a baking sheet without paper.

I would be glad to hear your comments on this if you repeat the idea.

3. Footprints

With bare children's feet we make an imprint on the heart.

footprints

We got it right the first time. Although the child practically does not stand still, but those seconds that we need to leave an imprint, he stood still, enthusiastically watching the process.

Using a spoon, make an inscription on the heart.

4. Baking in the oven

Preheating the oven up to 100 degrees and put a baking sheet with the print of the legs for baking for 3 hours.

5. Paint the imprint of the legs

After I took the print out of the oven, I gave it some time to cool down and then carefully peel off the baking paper.

AT original recipe it is written that almost immediately you can paint a heart, but I have it a couple more days lay down.

For painting I took acrylic paint. She dries quickly.

Paint the print of the legs

First I painted one side, and at the end of the day I painted the other.

Paint the print of the legs

You can also include a child in this process. Even if it turns out less accurately, but the main thing is the process. I haven't decided on this yet. We are now at an age when a child wants to do everything himself, he would not let me help, and at some point he himself could simply drop and break our imprint.

I am very pleased with the result. Now just need to find deep photo frame to put our present in it.

I didn't make a hole for hanging. The heart turned out to be not very light and could simply not withstand its weight, fall and break.

Please leave your feedback or comment. I'm very interested in your opinion!